GCodes

Aus RF1000 Wiki
Version vom 12. Dezember 2015, 13:53 Uhr von Jobo (Diskussion | Beiträge) (Die Seite wurde neu angelegt: „== Einleitung == Im folgenden findet ihr eine Auflistung Der GCodes, wie sie in den RF1000 Firmware Dateien dokumentiert sind == G-Codes == === G0 === Schnell…“)
(Unterschied) ← Nächstältere Version | Aktuelle Version (Unterschied) | Nächstjüngere Version → (Unterschied)
Zur Navigation springen Zur Suche springen

Einleitung

Im folgenden findet ihr eine Auflistung Der GCodes, wie sie in den RF1000 Firmware Dateien dokumentiert sind

G-Codes

G0

Schnelle lineare Bewegung

Parameter

X Y Z E

Siehe auch G1

G1

Lineare Bewegung

Parameter

X Y Z E

G2

Bogen im Uhrzeigersinn

Parameter

[X Y I J E F]
X: Position, die auf der X-Achse angefahren werden soll
Y: Position, die auf der Y-Achse angefahren werden soll
Innn: the point in X space from current X pos. to maintain a const. dist. from
Jnnn: the point in Y space from curr. Y pos. to maintain a const. dist. from
E: the amount to extrude btw start pt & end pt
F: the feedrate per minute of move btw start pt and end pt (if supplied)

G3

Bogen gegen Uhrzeigersinn

Parameter

[X Y I J E F]
siehe G2

G4

Verzögerung

Parameter

S<Secunden> or P<Millisekunden>

G20

Einheiten für G0, G1 sind Zoll

Parameter

Keine

G21

Einheiten für G0, G1 sind cm

Parameter

Keine

G28

Home all axis or named axis.

Parameter

[X Y Z]

G29

Z-Probe at the 3 defined probe points

Parameter

S<0..2>
S = 1 measure avg. zHeight
S = 2 store avg zHeight
  • G30 P<0..3> - Single z-probe at current position P = 1 first measurement, P = 2 Last measurement P = 0 or 3 first and last measurement
  • G31 - Write signal of probe sensor
  • G32 S<0..2> P<0..1> - Autolevel print bed. S = 1 measure zLength, S = 2 measure and store new zLength
  • G90 - Use absolute coordinates
  • G91 - Use relative coordinates
  • G92 [X<value> Y<value> Z<value> E<value>] - Set current position to cordinates given
  • G131 - set extruder offset position to 0 - needed for calibration with G132
  • G132 - calibrate endstop positions. Call this, after calling G131 and after centering the extruder holder.

M-Codes

Generelle M-Codes

  • M104 - Set extruder target temp
  • M105 - Read current temp
  • M106 - Fan on
  • M107 - Fan off
  • M109 - Wait for extruder current temp to reach target temp.
  • M111 S<0....9> - Set Debug Level (not documented in RF1k firmware?)
  • M114 - Display current position

Custom M Codes

  • M20 - List SD card
  • M21 - Init SD card
  • M22 - Release SD card
  • M23 - Select SD file (M23 filename.g)
  • M24 - Start/resume SD print
  • M25 - Pause SD print
  • M26 - Set SD position in bytes (M26 S12345)
  • M27 - Report SD print status
  • M28 - Start SD write (M28 filename.g)
  • M29 - Stop SD write
  • M30 <filename> - Delete file on sd card
  • M32 <dirname> - Create subdirectory
  • M42 P<pin number> S<value 0..255> - Change output of pin P to S. Does not work on most important pins.
  • M80 - Turn on power supply
  • M81 - Turn off power supply
  • M82 - Set E codes absolute (default)
  • M83 - Set E codes relative while in Absolute Coordinates (G90) mode
  • M84 - Disable steppers until next move, or use S<seconds> to specify an inactivity timeout, after which the steppers will be disabled. S0 to disable the timeout.
  • M85 - Set inactivity shutdown timer with parameter S<seconds>. To disable set zero (default)
  • M92 - Set axisStepsPerMM - same syntax as G92
  • M99 S<delayInSec> X0 Y0 Z0 - Disable motors for S seconds (default 10) for given axis.
  • M104 S<temp> T<extruder> P1 F1 - Set temperature without wait. P1 = wait for moves to finish, F1 = beep when temp. reached first time
  • M105 X0 - Get temperatures. If X0 is added, the raw analog values are also written.
  • M112 - Emergency kill
  • M115 - Capabilities string
  • M116 - Wait for all temperatures in a +/- 1 degree range
  • M117 <message> - Write message in status row on lcd
  • M119 - Report endstop status
  • M140 S<temp> F1 - Set bed target temp, F1 makes a beep when temperature is reached the first time
  • M190 - Wait for bed current temp to reach target temp.
  • M201 - Set max acceleration in units/s^2 for print moves (M201 X1000 Y1000)
  • M202 - Set max acceleration in units/s^2 for travel moves (M202 X1000 Y1000)
  • M203 - Set temperture monitor to Sx
  • M204 - Set PID parameter X => Kp Y => Ki Z => Kd S<extruder> Default is current extruder. NUM_EXTRUDER=Heated bed
  • M205 - Output EEPROM settings
  • M206 - Set EEPROM value
  • M207 X<XY jerk> Z<Z Jerk> E<ExtruderJerk> - Changes current jerk values, but do not store them in eeprom.
  • M220 S<Feedrate multiplier in percent> - Increase/decrease given feedrate
  • M221 S<Extrusion flow multiplier in percent> - Increase/decrease given flow rate
  • M231 S<OPS_MODE> X<Min_Distance> Y<Retract> Z<Backlash> F<ReatrctMove> - Set OPS parameter
  • M232 - Read and reset max. advance values
  • M233 X<AdvanceK> Y<AdvanceL> - Set temporary advance K-value to X and linear term advanceL to Y
  • M251 Measure Z steps from homing stop (Delta printers). S0 - Reset, S1 - Print, S2 - Store to Z length (also EEPROM if enabled)
  • M280 S<mode> - Set ditto printing mode. mode: 0 = off, 1 = on
  • M300 S<Frequency> P<DurationMillis> play frequency
  • M303 P<extruder/bed> S<printTemperature> X0 - Autodetect pid values. Use P<NUM_EXTRUDER> for heated bed. X0 saves result in EEPROM.
  • M320 - Activate autolevel
  • M321 - Deactivate autolevel
  • M322 - Reset autolevel matrix
  • M340 P<servoId> S<pulseInUS> : servoID = 0..3, Servos are controlled by a pulse with normally between 500 and 2500 with 1500ms in center position. 0 turns servo off.
  • M350 S<mstepsAll> X<mstepsX> Y<mstepsY> Z<mstepsZ> E<mstepsE0> P<mstespE1> : Set microstepping on RAMBO board
  • M400 - Wait until move buffers empty.
  • M401 - Store x, y and z position.
  • M402 - Go to stored position. If X, Y or Z is specified, only these coordinates are used. F changes feedrate for that move.
  • M500 Store settings to EEPROM
  • M501 Load settings from EEPROM
  • M502 Reset settings to the one in configuration.h. Does not store values in EEPROM!
  • M908 P<address> S<value> : Set stepper current for digipot (RAMBO board)
  • M3000 - turn off the Z compensation
  • M3001 - turn on the Z compensation
  • M3002 - configure the no compensation steps
  • M3003 - configure the max compensation steps
  • M3004 - configure the manual compensation steps
  • M3005 - enable custom debug outputs
  • M3006 - configure the static z-offset (units are [µm]) [needs M3001 to work] ### new in 0.91.49 ###
  • M3007 - configure the min z-compensation offset (units are [µm]) ### new in 0.91.49 ###
  • M3008 - configure the max z-compensation offset (units are [µm]) ### new in 0.91.49 ###
  • M3010 - start/abort the heat bed scan
  • M3011 - clear the compensation matrix from the EEPROM
  • M3012 - restore the default scan parameters
  • M3013 - output the current compensation matrix
  • M3020 - configure the x start position for the heat bed scan
  • M3021 - configure the y start position for the heat bed scan
  • M3022 - configure the x step size for the heat bed scan
  • M3023 - configure the y step size for the heat bed scan
  • M3024 - configure the x end position for the heat bed scan
  • M3025 - configure the y end position for the heat bed scan
  • M3030 - configure the fast step size for moving of the heat bed up during the heat bed scan
  • M3031 - configure the slow step size for moving of the heat bed up during the heat bed scan
  • M3032 - configure the fast step size for moving of the heat bed down during the heat bed scan
  • M3033 - configure the slow step size for moving of the heat bed down during the heat bed scan
  • M3040 - configure the delay (in ms) between two fast movements during the heat bed scan
  • M3041 - configure the delay (in ms) between two slow movements during the heat bed scan
  • M3042 - configure the delay (in ms) between reaching of a new x/y position and the test of the
    idle pressure
  • M3050 - configure the contact pressure delta (in digits)
  • M3051 - configure the retry pressure delta (in digits)
  • M3052 - configure the idle pressure tolerance (in digits)
  • M3053 - configure the number of A/D converter reads per pressure measurement
  • M3054 - configure the delay (in ms) between two A/D converter reads
  • M3055 - configure the pressure tolerance (in digits) per pressure measurement
  • M3005 - enable custom debug outputs
  • M3070 S1|S2 (req'd) - pause print as if "Pause" button was pressed - S1= pause at current position, S2= move to standard or predefined position (via M3105) and pause
  • M3071 - wait until the print has been continued via the "Continue" button ### new in 0.91.49 ###
  • M3079 - output the printed object
  • M3080 - park the printer
  • M3090 - test the watchdog (this command resets the firmware)
  • M3091 - erase the external EEPROM
  • M3100 - configure the number of manual z steps after the "Heat Bed up" or "Heat Bed down" button
    has been pressed
  • M3101 - configure the number of manual extruder steps after the "Extruder output" or "Extruder
    retract" button has been pressed
  • M3102 - configure the offset in x, y and z direction as well as the extruder retract which shall
    be applied in case the "Pause Printing" button has been pressed (units are [steps])
  • M3103 - configure the x, y and z position which shall set when the printer is parked
    deleted in 0.91.48 # (M3104 has been removed because all of its functionality is replaced through the OUTPUT_OBJECT_SCRIPT script now) - M3104 - configure the x, y and z position which shall set when the printed object is output
  • M3105 - configure the offset in x, y and z direction as well as the extruder retract which shall be applied in case the "Pause Printing" button has been pressed (units are [mm])
  • M3110 - lock the current status text
  • M3120 - turn on the case fan
  • M3121 - turn off the case fan

the following M Codes are for the work part scan in operating mode "mill"

  • M3130 - start/stop the search of the z-origin
  • M3140 - turn the z-compensation off
  • M3141 - turn the z-compensation on
  • M3146 - configure the static z-offset (units are [µm])
  • M3149 - get/choose the active work part z-compensation matrix
  • M3150 - start/abort the work part scan
  • M3151 - clear the specified z-compensation matrix from the EEPROM
  • M3152 - restore the default scan parameters
  • M3153 - output the specified work part z-compensation matrix
  • M3160 - configure the x start position for the work part scan (units are [mm])
  • M3161 - configure the y start position for the work part scan (units are [mm])
  • M3162 - configure the x step size for the work part scan (units are [mm])
  • M3163 - configure the y step size for the work part scan (units are [mm])
  • M3164 - configure the x end position for the work part scan (units are [mm])
  • M3165 - configure the y end position for the work part scan (units are [mm])

other M Codes

  • M3200 - reserved for test and debug
Abgerufen von „https://www.rf1000.de/wiki/index.php?title=GCodes&oldid=252“